Drive-In Rack in Santa Fe Springs, CA
Drive-in rack in Santa Fe Springs, CA gives manufacturers and industrial suppliers the densest way to hold bulk pallets of a few part numbers. Instead of one aisle per row, forklifts travel inside the structure on guided lanes.
We are a division of Warehouse Equipment & Supplies Co., which has supplied and installed rack since 1997. I have spent over 25 years measuring buildings and loads before drawing any lane.
What Drive-In Pallet Rack Does Differently
Picture a block of uprights tied together with continuous load rails on each side of every bay. The lift drives in, lowers the pallet onto those rails and reverses out. Next pallet goes just in front. Repeat until the bay is full, then move to the next lane and start again at the back.
Because everything enters and exits one face, drive-in storage runs last in, first out. Raw stock like bar ends, packaged fasteners or production consumables rarely cares about age, so that pattern works.
Should order of arrival matter, drive-thru racking puts an access aisle at both ends. Receiving loads one side; production pulls from the other.
Lift choice shapes the whole block. Sit-down counterbalance trucks need wider bay openings than narrow reach models, and a tall mast may limit the highest rail level. We measure every truck you plan to use inside the lanes, including any rental units brought in during busy months.
A Santa Fe Springs drive-in rack block often sits beside cantilever arms or selective bays holding long stock and mixed parts. We draw those zones together so forklifts approaching the dense lanes never have to swing through bundle turning room.
Lane count follows part count. If you stock eight bulk items, plan roughly eight lanes, each sized to the pallets of that item you hold at peak. Mixing two part numbers in one drive-in pallet rack lane traps the rear item until the front clears.
Heavy industrial pallets demand careful rail selection. We confirm the heaviest load, pallet bottom construction and any overhang. Steel or plastic bases each sit on rails differently, so we check samples.
Fewer pallets per part number points toward pushback rack in Santa Fe Springs, where each level keeps its own face. Batches feeding assembly in arrival order fit pallet flow rack in Santa Fe Springs. Component options are covered on our drive-in rack product page.
Drive-In Rack Around Florence Ave and Santa Fe Springs Rd
Santa Fe Springs sits on I-5 and I-605, with facilities along Santa Fe Springs Rd and Florence Ave mixing fabrication, industrial supply and aerospace supplier work under one roof.
Those mixed buildings rarely have spare floor. Shop areas, bundle turning room and receiving all compete for space with stored inventory. Collapsing a bulk reserve area into dense lanes frees ground for production.
Most local buildings are older tilt-up or masonry with modest clear heights, so we size levels around what your lift can reach safely. Our Santa Fe Springs service area page lists every other system we supply locally.
Operations We Rack Around Here
Local industrial areas and access routes include Santa Fe Springs Rd, Florence Ave, I-5 and I-605.
From Load List to Installed Drive-Thru Racking
Supplier warehouses need storage that stays clear of shop traffic. Our planning steps reflect that.
Load list
We record part numbers, pallet counts, pallet weights and base types for every candidate item.
Floor routes
We map fabrication transfers and receiving paths so lanes do not block shop movement.
Lane and rail spec
Rail profile, guide rails and bay width are chosen for your heaviest pallet and lift.
Install and handoff
Experienced installation crews we schedule and manage build the block and walk operators through it.
Get a Drive-In Rack Quote for Your Santa Fe Springs Warehouse
Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (213) 715-0940.
Los Angeles Pallet Rack
835 Wilshire Blvd
Ste 500 #653
Los Angeles, CA 90017
(213) 715-0940Monday - Friday: 8:00 AM - 6:00 PM
Drive-In Rack Questions We Hear Most
Warehouse Storage Services in Santa Fe Springs
Pallet Rack
Every pallet reachable, every time. The baseline we size everything else against.
View details
Pushback Rack
Two to six pallets deep from one aisle, without giving up much reach.
View details
Pallet Flow Rack
Load one side, pick the other, and let gravity enforce first in, first out.
View details
Cantilever Rack
Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.
View details
Carton Flow Rack
Cases advance to the picker instead of the picker hunting for cases.
View detailsWarehouse Relocation
Rack teardown, labeled moves and reinstallation planned around the new building and your inventory cutover.
View detailsNearby Areas We Also Serve
Our delivery and installation territory covers Greater Los Angeles and the Inland Empire, so one team can handle multiple buildings for the same company.
Where We Work
Based in Los Angeles, we serve greater Los Angeles and the Inland Empire with industrial pallet racks and warehouse storage solutions.
Los Angeles Pallet Rack
Address
835 Wilshire Blvd
Ste 500 #653
Los Angeles, CA 90017
Phone
(213) 715-0940Business Hours
Monday - Friday: 8:00 AM - 6:00 PM
Saturday: Closed
Sunday: Closed
Need Drive-In Rack in Santa Fe Springs?
Call (213) 715-0940 or request a quote and we will get a layout started.